What problems should be paid attention to in the welding process of ultrasonic welding machine?

Aug 24, 2022

【1】 After ultrasonic welding, the product always burns on one side

Ultrasonic vibration welding is not a simple linear longitudinal vibration (flexural and transverse vibration are not included in this discussion), but a cross type longitudinal downward vibration. The energy at the ultrasonic output end of the upper mode also has a certain strength distribution point. Although the pressure, voltage and machine determine the stability of the power output energy, the energy distribution point also shows a proportional increase or decrease.

If it is found that the product is always scalded at a single point during ultrasonic welding, it means that the output energy at this point of the upper mold corresponds to the stress formed at this point of the product. At this time, if the contact point of the ultrasonic vibration surface is changed, the scald caused by the thermal energy bundle can be improved.

Ultrasonic welding is a high-tech technology for welding thermoplastic products. All kinds of thermoplastic adhesive parts can be treated by ultrasonic welding without adding solvent, adhesive or other auxiliary materials. Its advantages are to increase productivity, reduce cost and improve product quality.

Ultrasonic plastic welder principle: 20kHz (or 15KHz) high-voltage and high-frequency signals are generated by the generator. The signals are converted into high-frequency mechanical vibration through the energy conversion system, which is applied to the plastic products and workpieces

The friction between the working surface and internal molecules causes the temperature transmitted to the interface to rise. When the temperature reaches the melting point of the workpiece itself, the welding interface of the workpiece will melt quickly, and then fill the gap between the interfaces. When the vibration stops, the workpiece

At the same time, it is cooled and shaped under certain pressure to achieve perfect welding.

【2】 How to solve the problem of ultrasound welding when power is on

Analysis reason:

1. The ammeter moves after startup

2. The ammeter does not move after startup

resolvent:

1. Check whether the mainboard is damaged and repair the mainboard

It's not a big problem, it may be disturbed

【3】 Influence of plastic parts materials on ultrasonic welding

1. The ultrasonic wave propagates in the plastic parts, and the plastic parts absorb and attenuate the ultrasonic energy more or less, thus having a certain impact on the ultrasonic processing effect. The plastic is generally divided into amorphous materials and hard glue according to the hardness

There is also a difference between soft rubber and modulus. Generally speaking, the ultrasonic processing performance of plastics with high hardness and low melting point is better than that of plastics with low hardness and high melting point. Therefore, this involves the problem of the distance of ultrasonic machining,

2. Influence of processing conditions of plastic parts on ultra sonic welding

Different processing forms of plastic parts such as injection molding, extrusion or blow molding and different processing conditions will have certain influence on ultrasonic welding.

A: Humidity defect: the humidity defect is generally formed in the process of making striped or loose plastic parts. The humidity defect attenuates the useful energy during welding, makes the sealing position water seepage, and lengthens the welding time. Therefore, the plastic parts with high humidity should be dried before welding. Such as polyoxymethylene.

B: Influence of injection molding process:

The adjustment of injection process parameters may cause the following defects:

① Dimensional change (shrinkage, bending deformation)

② Weight change

③ Surface damage

④ Poor uniformity

C: Storage period: after the plastic parts are processed by injection molding, they are generally placed for at least 24 hours before welding to eliminate the stress and deformation of the plastic parts. Plastic parts made of amorphous plastic by injection molding may not meet this requirement.

D: Recycled plastic

Recycled plastic has poor strength and poor adaptability to ultrasonic welding. Therefore, if recycled plastic is used, various design dimensions shall be considered as appropriate.

E: Release agent and impurities

Release agent and impurities have certain influence on ultrasonic welding. Although the solvent and impurities on the processing surface can be shaken off during ultrasonic processing, it is not necessary to seal or operate under high ultrasonic wave

The sound wave whose frequency is higher than the upper limit of human hearing (about 20000 Hz) is called ultrasonic wave, or ultrasonic wave.

ultrasonic welder